AA 2014 matrisli-B4C parçacık takviyeli kompozit üretimi ve özelliklerinin incelenmesi
Manufacturing of AA 2014 Matrix-B4C particulate composites and investigating properties
- Tez No: 78166
- Danışmanlar: PROF. DR. FAZLI ARSLAN
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Bor karbür, Kompozit malzemeler, Mekanik özellikler, Vorteks, Metal matrixcomposites, Particulate composites, Boron carbide, Vortex method, Mechanical properties, Composite materials, Vortex
- Yıl: 1998
- Dil: Türkçe
- Üniversite: Karadeniz Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
ÖZET Bu çalışmada matris malzemesi olarak AA 2014 alüminyum alaşımı, parçacık olarak da bor karbür (B4C) kullanılarak sıvı ortamda
Özet (Çeviri)
SUMMARY In this study metal matrix particulate reinforced composite was manufactured using AA2014 alumium alloy matrix and B4C particulate. Mechanical properties of manufactured composites such as hardness, tensile strength and elongation after fracture at different particul volume ratios were also investigated. It is very difficult to manufacture these composites because of bad wetting of liquid matrix of B4C particles. It is necessary to heat the liquid matris up to 1000°C in order to improve wetting properties. But this comparatively high temperature causes Excessive oxidation and gas entrapment in liquid metal. A new method was developped in this study which is based on cleaning of particule surfaces using an acid (% 50 HF +% 50 H2SO4) mixture before mixing with liquit alloy. B4C particles were dried at 150 °C for 12 -24 hours and preheated to 400 °C before adding to liquit alloy at 680°C. The results of microscopic examinations showed the particles were held inthe matrix and homogeneous mixture was obtained. Particle volume ratios were changed between % 1.5 to % 12 and the relations between particle volume ratios hardness and tensile strength and elongation after fracture were investigated. The test results showed that tensile strengths and elongations were decreasing with increasing particle content. This was attributed to ease of crack formation B4C/matris interfaces. Hardness test results indicated that hardness was increasing with particle volume ratio up to % 9. But it was decreasing again because of excessive porosity formation.
Benzer Tezler
- Partikül takviyeli AA 2014 metal matrisli kompozit malzemenin infiltrasyon yöntemi ile üretimi ve özelliklerinin karakterizasyonu
Investigation on the properties of particulate reinforced AA 2014 metal matrix composite materials produced by vacuum infiltration method
ONUR OKUR
Yüksek Lisans
Türkçe
2016
Metalurji MühendisliğiYıldız Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. SİBEL DAĞLILAR
PROF. DR. RECEP ÇALIN
- AA2014-B4C metal matrisli kompozitinin toz metalurjisi ve infiltrasyon yöntemiyle üretilebilirliği, karakterizasyonu ve aşınma özelliklerinin incelenmesi
Producibility of AA2014-B4C metal matrix composite by powder metallurgy and infiltration method, characterization and research of wear
UFUK TAŞCI
Yüksek Lisans
Türkçe
2012
Metalurji MühendisliğiGazi ÜniversitesiMetal Eğitimi Ana Bilim Dalı
DOÇ. DR. BÜLENT BOSTAN
- Alüminyum üzerine uygulanan kompozit kaplamaların aşınma davranışının incelenmesi
Investigation of wear behaviour of composite coatings deposited on aluminium
FATİH KILIÇ
- Toz metalurjisi yöntemiyle üretilen AA2024 - B4C kompozitlerinin özelliklerinde PCA katkısının incelenmesi
Investigation of PCA addition in the properties of AA2024 - B4C composites produced by powder metallurgy method
SEDAT ALPEREN TUNÇ
Yüksek Lisans
Türkçe
2024
Mühendislik BilimleriKaradeniz Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. AYKUT ÇANAKÇI
- AA 2014/Al2o3 metal matrisli kompozitin mekanik alaşımlama yöntemi ile üretimi ve yaşlandırılabilme özelliklerinin araştırılması
The research of the manufacture of AA 2014/Al2o3 the composite with metal matrix through mechanic alloying method and the properties of age hardenable process
ALPER YILMAZ
Yüksek Lisans
Türkçe
2013
Metalurji MühendisliğiGazi ÜniversitesiMetal Eğitimi Ana Bilim Dalı
YRD. DOÇ. DR. NECATİ YALÇIN
DOÇ. DR. BÜLENT BOSTAN