İki farklı tam seramik sistemin kullanıldığı üç üyeli sabit protez mukavemetinin sonlu elemanlar stres analizi ile incelenmesi
Strength assessment of two all ceramic systems used for posterior fixed dentures by finite element analysis
- Tez No: 157671
- Danışmanlar: DOÇ.DR. HAKAN UYSAL
- Tez Türü: Doktora
- Konular: Diş Hekimliği, Dentistry
- Anahtar Kelimeler: Elastisite modülü, Bükülme dayanımı, Konnektör tasarımı, Sonlu elemanlar stres analizi, Tam seramik köprüler, Modulus of elasticity, Flexural strength, Connector design, Finite element analyses, All ceramic bridge
- Yıl: 2004
- Dil: Türkçe
- Üniversite: Çukurova Üniversitesi
- Enstitü: Sağlık Bilimleri Enstitüsü
- Ana Bilim Dalı: Protetik Diş Tedavisi Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 79
Özet
ÖZET iki Farklı Tam Seramik Sistemin Kullanıldığı Üç Üyeli Sabit Protez Mukavemetinin Sonlu Elemanlar Stres Analizi ile İncelenmesi Bu çalışmanın amacı In Cream Zirconia ve IPS Empress 2 sistemlerinin mekanik özelliklerini belirlemek ve sonlu elemanlar modeli üzerinde mekanik davranışını inceleyerek, posterior tek diş eksikliğinin sabit protez ile tedavisinde kullanıma uygunluğunu değerlendirmektir. ICZ ve 1PSE2 sistemlerinin elastisite modülü ve bükülme dayanımları mekanik deneylerle tespit edildi. Elastisite modülü, TSE EN 843-1 numaralı test protokolü takip edilerek 3 nokta eğme testi ile, bükülme dayanımı ise ISO 6872 numaralı test protokolü izlenerek '3 destek küreli piston' tekniği ile tespit edildi, iler deneyde, o test standardında belirtilen boyutlarda hazırlanan 10 ar örnek kullanıldı. Normal dağılım gösteren deney bulguları Student t testi ile karşılaştırıldı. ICZ sisteminin elastisite modülü ve bükülme dayanımı sırayla 219,1±9,3 GPa ve 606,8±41,7 Mpa, IPSE2 sisteminin ise 97,5±2,8 GPa ve 310,7 ± 50,8 MPa olarak hesaplandı. Seramik sistemlerin çiğneme kuvvetleri altındaki davranışı Sonlu Elemanlar Stres Analizi ile incelendi. Maksiller 2. premolar diş eksikliğinin 3 üyeli sabit protez ile tedavi edildiği, 16mm2 ve 9 mm2 konnektör kesit alanına sahip iki protez modeli oluşturuldu. Modeller 100N ve 600 N ile santral fossadan dik ve bukkal kaspın palatinal eğimi ile palatinal kaspııı bukkal eğiminden 45° açı ile yüklendi. Modellerdeki çekme gerilimleri, seramikler için güvenlik sınırı olan bükülme dayanımlarının %40'ı ile karşılaştırıldı. 100N yüklemede modellerde güvenlik sınırını aşan gerilimler oluşmadı. 600N'luk dik yüklemede 9mm2 konnektör kesit alanlı modellerin kaplama seramiğinde, palatinal kasptan uygulanan 600N'luk eğimli yüklemede 16mm2 konnektör kesit alanlı ICZ sistemi hariç tüm modellerde ve bukkal kasptan uygulanan 600N'luk eğimli yüklemede bütün modellerde güvenlik sınırı aşıldı. Çalışmanın sınırları içerisinde her iki seramik sisteminin de normal çiğneme kuvvetleri altında başarı ile kullanılabileceği, yeterli konnektör kalınlığı sağlanabilirse ICZ'nin eğimle uygulanan yüksek çiğneme kuvvetlerine de dayanabileceği gösterilmiştir.
Özet (Çeviri)
ABSTRACT Strength assessment of two all ceramic systems used for posterior fixed dentures by Finite Element Analysis. The aim of this study was to determine the mechanical properties of In- Ceram Zirconia and IPS Empress 2 all ceramic systems and evaluate their mechanical behaviors in a three unit posterior fixed prosthesis through finite element model. The flexural strength of the materials was determined by“piston on 3 ball”technique in test standard ISO 6872. TS ENV 843-1 was followed to determine the modulus of elasticity. 10 specimens for each material were used in dimensions dictated by the test standards. The flexural strength and the elastic modulus of ICZ were 606,8±41,7 Mpa, 219,1±9,3 GPa and IPSE2 were 310,7±50,8 MPa, 97,5±2,8 GPa respectively. Student-t test revealed statistically significant difference between groups at 0.1 level. The effects of loads on ceramics were examined through finite element models of a three unit bridge. Two models differed from each other with only the connector cross-sectional areas of 16mm2 and 9mm2. Loads of 100N and 600N were applied first perpendicular to the occlusal plane at the central fossa, then with a 45" angle to the sagittal plane at the buccal incline of palatinal cusp and at the palatal incline of buccal cusp. The maximum tensile stresses were compared with 40% of the flexural strengths of ceramics. All ceramics survived at 100N. At 600N perpendicular loading, veneer ceramics of models with 9mm2 connector area were failed. Except ICZ having 16mm2 connector with angled loading at palatinal cusp, none of the ceramics were reliable. None of the models at 600N buccal cusp loadings did survive. Within the limitations of the study, either of the ceramic systems was found to be resistant to the normal bite forces. Either of the materials may fail at higher limits of intraoral forces with a connector cross sectional area of 9mm2. Failure of ICZ may not be expected even at higher limits of intraoral forces if the connector cross sectional area is sufficiently extended.
Benzer Tezler
- Anterior dişlerde zirkonyum oksit post üzerine üretilen farklı tam seramik kor materyallerinin kırılma dayanıklılığının incelenmesi
Fracture strength evaluation of different all ceramic core materials constructed onto zirconium posts
NİHAL ÖZCAN
Doktora
Türkçe
2010
Diş HekimliğiHacettepe ÜniversitesiProtetik Diş Tedavisi Ana Bilim Dalı
PROF. DR. ERDAL ŞAHİN
- İki farklı tam seramik kor materyalinin baskı dayanıklılığı ve marjinal uyumu üzerine farklı marjinal dizayn ve taper açılarının etkisi
The effect of different margin designs and taper angles on the compressive strength and marginal fit of two different all ceramic cores
H.NALAN BOZOĞULLARI
Doktora
Türkçe
2007
Diş HekimliğiSelçuk ÜniversitesiProtetik Diş Tedavisi Ana Bilim Dalı
PROF.DR. ÖZGÜR İNAN
- Farklı materyaller ile restore edilmiş farklı bağlantı sistemlerine sahip konometrik tek kron restorasyonlarda stres dağılımının 3 boyutlu sonlu elemanlar analizi ile değerlendirilmesi
Evaluation of stress distribution in conometric single crownrestorations with different connection systems restored with different materials using3d finite element analysis
SİNEM VURAL
Doktora
Türkçe
2024
Diş HekimliğiMarmara ÜniversitesiProtetik Diş Tedavisi Ana Bilim Dalı
DOÇ. DR. BUKET EVREN
- Farklı CAD-CAM seramik materyallerin kalınlıklarının ölçüm yapılan arka zemin tipine göre maskeleme yeteneğine etkisi ve yarı saydamlığın değerlendirilmesi
Effect of thickness of different CAD-CAM ceramic materials on masking ability according of the measured background TYPE and evaluation of translucency
TANSU BURSALI
Diş Hekimliği Uzmanlık
Türkçe
2022
Diş HekimliğiSelçuk ÜniversitesiProtetik Diş Tedavisi Ana Bilim Dalı
PROF. DR. İSA YÖNDEM
- Çoklu fırınlama uygulamasının farklı zirkonya esaslı alt yapı sistemlerinin mekanik özelliklerine etkisi
Effect of repeated firing on mechanical properties of different zirconia based ceramic core systems
BEHİYE DABAKOĞLU
Doktora
Türkçe
2009
Diş HekimliğiYeditepe ÜniversitesiProtetik Diş Tedavisi Ana Bilim Dalı
PROF. DR. ENDER KAZAZOĞLU