Geri Dön

Sıcaklık genleşmesi farklı iki malzemeden yapılmış levhalarda termal gerilmelerin analizi

A thermal stress analysis on plates produced by two materials with different thermal expansions

  1. Tez No: 507637
  2. Yazar: TUĞBA BAYTAK
  3. Danışmanlar: DR. ÖĞR. ÜYESİ OSMAN BULUT
  4. Tez Türü: Yüksek Lisans
  5. Konular: İnşaat Mühendisliği, Civil Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2018
  8. Dil: Türkçe
  9. Üniversite: İstanbul Teknik Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: İnşaat Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Yapı Mühendisliği Bilim Dalı
  13. Sayfa Sayısı: 95

Özet

Yapısal elaman olarak birçok alanda kullanılan kompozit levhalar, üretim ve işletme sırasında termal etkilere maruz kalmaktadırlar. Çeşitli etkiler nedeniyle bu levhaların birleşimi oluşturan malzemelerinin değişik konumlarında ve farklı geometrilerde oluşan kusurlar, gerilme yığılmalarına neden olmakta ve yapı güvenliğini tehlikeye sokmaktadırlar. Yapılarda güvenli tasarım yapılabilmesi için malzemelerde sıcaklık etkisiyle oluşan termal gerilme dağılımlarının, gerilmelerin maksimum olduğu bölgelerin ve kusur bölgelerindeki gerilme yığılmalarının belirlenmesi gerekir. Bu çalışmada ısıl genleşme katsayıları farklı olduğundan dolayı sıcaklık genleşmesi farklı olan iki malzemeden imal edilmiş levhanın termal gerilme analizi yapılmıştır. Kompoziti oluşturan malzemelerin diğer mekanik özellikleri aynıdır. Bu tür bir uygulama nükleer reaktörlerin basınç kaplarında görülmektedir. Bu elemanlar çelik gövdenin paslanmaz çelik ile kaplanması ile üretilmektedirler. Ele alınan problem öncelikle fotoelastisite yöntemi ile deneysel olarak çalışılmıştır. Deneysel çalışmada fototermoelastisitenin mekanik modelleme yöntemi kullanılmıştır. Prototipin deneysel olarak modellenmesi için literatürde bulunan iki farklı termoelastisite problemi arasındaki şekil değiştirmelerin analojisi kullanılmıştır. Bu analojiye göre mekanik özellikleri aynı ve ısıl genleşme katsayıları farklı iki malzemenin aynı sıcaklık değişimine maruz kalması durumu, aynı iki levha birleşiminde parçaların farklı sıcaklık değişimine maruz kalması durumu ile modellenmiştir. Bu nedenle deney modeli, malzemesi aynı iki silindirik levhadan oluşturulmuştur. Bu levhaların farklı sıcaklık değişimine maruz kalması problemi ele alınmıştır. Kullanılan malzeme epoksi esaslı Araldite olup, homojen, izotrop, lineer-elastik ve optik hassas malzemedir. Deneyde kullanılacak malzemenin mekanik ve optik özellikleri model oluşturulmadan önce belirlenmiştir. Termal etkinin oluşacağı parçada $\alpha\Delta T$ şekil değiştirmesi fotoelastisitenin mekanik modelleme yöntemi ile oluşturulmuştur ve oluşan şekil değiştirmeler şekil değiştirmelerin dondurulması yöntemi ile levhada sabitlenmiştir. Şekil değiştirmelerin dondurulduğu parça ile aynı boyutlarda üzerinde herhangi bir etki bulunmayan parça özel işlemlerle yapıştırılmıştır. Ardından modelde, kendisini oluşturan parçaların birleşim yüzeyine dik ve birleşimi geçen bir kusur oluşturulmuştur. Oluşturulan bu kusur gerçekte karşılaşılan kusur tiplerinden birisi olarak belirlenmiştir. Bu şekilde üzerinde kusur bulunduran, iki levhanın birleşimiyle oluşturulmuş, silindirik geometrideki deneysel model elde edilmiştir. Model, viskoelastik sıcaklık değerine kadar özel ısıtma rejimiyle ısıtıldığında termal şekil değiştirmelerin dondurulduğu parçadaki şekil değiştirmeler serbestleşmiş fakat yüksüz parça buna izin vermediği için modelde yeni bir gerilme dağılımı oluşmuştur. Elde edilen bu gerilme dağılımı prototipteki termal gerilme dağılımını göstermektedir. Ardından model, özel soğutma rejimi ile oda sıcaklığına soğutulduğunda, bu şekil değiştirmeler modelde sabitlenmiştir. Termal gerilmelerin analizi için üç boyutlu fotoelastisitenin dilim alma yöntemi kullanılmıştır. Modelde serbest yüzeylerde, malzemelerin birleşim yüzeyinde, kusur ve kenar etkilerinin olmadığı bölgede, oyuk etrafında ve oyuğa dik doğrultuda gerilme dağılımlarını elde etmek amacıyla modelden çapı doğrultusunda 1.3 mm kalınlığında bir dilim çıkarılmıştır. Gerilme değerlerinin elde edileceği her bir nokta için polarize mikroskopta şerit sayısı ölçümü yapılmıştır ve bu noktalar için ışığın geçtiği kalınlık değerleri dijital mikrometre ile belirlenmiştir. Malzemenin optik hassasiyet katsayısı, ölçüm yapılan noktalardaki şerit sayıları ve ışığın geçtiği kalınlık değerleri bilindiğinden ilgili formül ile her nokta için asal gerilmelerin farkı değerleri hesaplanmıştır. Hesaplanan bu gerilmeler boyutsuz gerilmelere dönüştürülerek, boyutsuz gerilmelerin dağılımı çizilmiştir. Bahsedilen dilimin üst kenarına komşu elemanlarda asal gerilme bileşenlerinden biri sıfır olduğundan dolayı, bu bölgede ayrı bir dilim alınarak gerilmelerin ayrılması sağlanmıştır. Yine oyuk etrafında gerilmelerin teğetsel bileşenlerinin dağılımı elde edilmiştir. Oyuk etrafında da farklı dilimler alınarak gerilmelerin ayrılması sağlanmıştır. Modelde analitik çözümün geçerli olduğu bölgelerde gerilme dağılımları, literatürde bulunan levhada sıcaklık etkisinin levha kalınlığı doğrultusundaki koordinat değişimine bağlı olması durumları için verilen termal gerilme denklemleri kullanılarak elde edilmiştir. Analitik çözüm yapılırken deneyde oluşturulan modelin malzeme özellikleri ve boyutları kullanılmıştır. Analitik çözüm ile elde edilen gerilme dağılımları deneyde analitik çözüme uygun doğrultudan elde edilen dağılımlarla karşılaştırılarak deneysel sonuçların uygunluğu gösterilmiştir. Analitik çözümün geçerli olmadığı bölgelerde deneysel verilerin karşılaştırılması için sonlu eleman yöntemi kullanılarak sayısal analiz yapılmıştır. Bu analiz için ABAQUS paket programı kullanılmıştır. Sonlu eleman modelinin değişkenleri, önce literatürde verilen, üzerinde kusur bulundurmayan problemin çözümüne uygulanarak ağ iyileştirmesi ile belirlenmiştir. Ardından oyuk bulunduran deney modelinin sonlu eleman modeli analizi yapılmıştır. Elde edilen sonuçlardan ilgili doğrultulardaki gerilme değerleri analitik çözümle elde edilen sonuçlarla karşılaştırılarak sonuçların uygunluğu gösterilmiştir. Modelde gerilmelerin yoğunlaştığı oyuk tepe noktasında maksimum gerilme yığılması faktörü hesaplanmıştır. Ayrıca sonlu eleman analizi ile bulunan gerilme dağılımları deneyden elde edilen ilgili bölgelerdeki dağılımlarla karşılaştırılmıştır. Böylece sayısal modellemenin deney sonuçları ve analitik çözümle doğrulamaları yapılmıştır.

Özet (Çeviri)

Composite materials used in many areas as structural elements are exposed to thermal effects during production and operation. Especially, these materials are subjected to different types of mechanical or thermal effects during service. Due to these various effects, defects occur in different positions and in different geometries on the materials forming these plates. When thermal or mechanical effects are not taken into account, important stress concentrations can occur around these defects. Therefore, the expected strength in design cannot be ensured during the service life. Although there are lots of works on mechanical loads in literature, studies on thermal stress state around defects occured by temperature distribution are few. In order to be able to safely design of the structures, the thermal stress distributions and the stress concentrations around the defect should be determined. In this study, the thermal stress analysis of the plate made of two materials with different temperature expansions was performed. This plate has a cavity in the direction perpendicular to the plane of the interface. Mechanical properties of the composites are the same except for thermal expansion coefficients. Such an application is seen in pressure vessels of nuclear reactors. These elements are produced by coating the steel body with stainless steel. When DT is the temperature difference, thermal stresses will occur due to the different expansions of the materials. The problem that has been addressed is firstly studied experimentally with the method of photoelasticity. In the experimental study, mechanical modeling method of photo-thermoelasticity was used. For the experimental modeling of the prototype, the analogy of deformation between two different thermoelasticity problems in the literature was used. The first of these problems is the combination of two different materials having different thermal expansions subjected to the same temperature change. The second is about the plate made of a single material which are exposed different temperature change. The first problem is the prototype, the latter is the experimental analysis model. According to this analogy, the differences of thermal strains occurring in these two cases are equalized. The situation of prototype in which two materials with different coefficients of thermal expansion are subjected to the same temperature change was modeled by the case in which the parts are subjected to different temperature changes in a single material. Considering this modeling, the experimental model is made of same two cylindrical plates. The problem of different temperature changes of these plates has been studied in this work. The use of this analogy provides great ease in experimental modeling, because the thermal expansion coefficients, optical sensitivity coefficients and viscoelastic temperature of the materials are the same. By this way, a model was obtained which can be used practically for the method of strain freezing in photoelasticity. The material used in the experimental model is an epoxy-based material Araldite, which is homogeneous, isotropic and optical sensitive material. Linear-elastic behaviour is only considered. The mechanical and optical properties of the material were determined before the model was created. Viscoelastic temperature value, the coefficient of optical sensitivity and modulus of elasticity of the material were obtained by some photoelastic tests. Some of them were also determined by DMA (Dynamic Mechanical Analyzer). The strain, aDT, is formed by the mechanical modeling method and the formed strains are fixed in the plate by the freezing method of photoelasticity. To create the part on which the thermal effect occurs, a cylinder specimen, made from the same material with the model, was used. This specimen was loaded by axial pressure in the furnace, which is suitable for the photoelastic examination. In the furnace, the sample was heated to the viscoelastic temperature by a special regime of heating and an axial compression load was applied at this temperature. Then, the sample was cooled to room temperature with the same regime, and the strains occurring at the viscoelastic temperature were fixed at room temperature. From this specimen, a part whose thickness is 3.9 mm was obtained by a precision cutting in order to create the thermal loaded part of the experimental model. The diameter of the part is the same with the diameter of the part on which the mechanical strains are frozen. These parts were bonded to each other with a special process. Then, a cavity is formed in the model which is perpendicular to the interface of the parts. This cavity was actually identified as one of the types of defect encountered in the industrial applicatoins. In this way, an experimental model having the cylindrical geometry, formed by the combination of two plates, has been obtained. When the model was heated by the special heating regime up to the viscoelastic temperature, the strains on the part, on which the thermal deformations were frozen, were released, but since the unloaded part did not allow this, a new stresses distribution was formed through the model. This obtained stress distribution shows the thermal stress distribution in the prototype. Then, when the model is cooled to room temperature with the same special cooling regime, these deformations are fixed in the model. For the analyses of the thermal stresses, the method of slicing of three-dimensional photoelasticity was used. A slice including the tip of the cavity with a thickness of 1.3 mm was cut out in the diameter direction. The distribution of thermal stresses were obtained in the slice along the free surfaces, on the interface of the parts, along the thickness in the region without the effects of the cavity and edges, around the cavity and along the direction perpendicular to the cavity. For each point, where the stress values were obtained, the number of fringes are measured by a polarizing microscope and the thickness values of the light passes through the slice at these points were determined by the digital micrometer. Since the optical sensitivity coefficient of the material, the number of fringes at the measurement points, and the thickness values of the light passes through the slice were known, the difference values of the principal stresses were calculated for all points by the related formula. These calculated stresses were transformed into dimensionless stresses dividing them by Ee = EaDT and the distributions of dimensionless stresses were plotted. Since one of the principal stress components is zero in the elements adjacent to the upper edge of mentioned slice, an extra slice was cut out along this edge. Stresses found in the previous slice were substituted in the difference values of the stresses taken from the extra slice in order to separate the stresses. A graph of seperated stresses was obtained along this edge. Also, the distribution of the tangential components of the stresses around the cavity was obtained. For the regions where the analytical solution is valid in the model, the stress distribution were obtained using the thermal stress equations in the literature given for the case where the function of temperature change is a function of the coordinate variable in the plate thickness direction. In the analytical solution, the material properties and dimensions of the model created in the experiment were used. The stress distributions obtained by the analytical solution were compared with the distributions obtained in the appropriate direction from the experiment to show the consistency of the experimental data. Numerical analysis was also performed using the finite element method to compare the experimental data in regions where analytical solution is not available. ABAQUS, a finite element package program, was used for this analysis. Variables of the finite element model were firstly determined by mesh refinement applying the solution given in the literature, which has no discontinuity. Then, a finite element model of the experimental model with a cavity was developed. From the obtained results, the stress values in the relevant directions were compared with the results obtained from the analytical solution. The results have good agreement. In the model, the maximum stress concentration factor is calculated at the tip of cavity. In addition, the stress distributions obtained by the finite element analysis were compared with the distributions in the corresponding regions obtained from the experiment. Thus, the results from numerical modeling were verified by those from the analytical solution and experimental model.

Benzer Tezler

  1. Yeni Cami'nin akustik açıdan performans değerlendirmesi

    Evaluation of the acoustical performance of the New Mosque

    EVREN YILDIRIM

    Yüksek Lisans

    Türkçe

    Türkçe

    2003

    Mimarlıkİstanbul Teknik Üniversitesi

    Mimarlık Ana Bilim Dalı

    PROF. DR. SEVTAP YILMAZ DEMİRKALE

  2. Arayüzeyinde çatlak bulunan bimateryalin termomekanik incelenmesi

    Thermomechanical analysis of bimaterial an interfacial crack

    SÜLEYMAN TAŞGETİREN

    Doktora

    Türkçe

    Türkçe

    1997

    Makine MühendisliğiDokuz Eylül Üniversitesi

    PROF. DR. TEVFİK AKSOY

  3. Çan bölgesi linyitlerinin akışkan yatak yanma sürecindeki davranımı

    Fluidised bed combustion behaviour of the lignites from the Çan region

    HÜSNÜ ATAKÜL

    Doktora

    Türkçe

    Türkçe

    1986

    Kimya Mühendisliğiİstanbul Teknik Üniversitesi

    DOÇ.DR. EKREM EKİNCİ

  4. Yaygın gelişimsel bozukluğu (Otizm spektrumu) olan çocuklarda klinik ve elektroensefalografi bulguları.

    Başlık çevirisi yok

    SEMİH AYTA

    Tıpta Uzmanlık

    Türkçe

    Türkçe

    2006

    Nörolojiİstanbul Üniversitesi

    Nöroloji Ana Bilim Dalı

    PROF. DR. MEFKURE ERAKSOY

  5. Finite element based thermomechanical fatigue analysis of solder joints in electronic packages

    Elektronik paketlerde bulunan lehim topçuklarının sonlu elemanlar yöntemiyle ile yorulma analizleri

    HASAN SAĞDIÇ

    Yüksek Lisans

    İngilizce

    İngilizce

    2024

    Makine MühendisliğiOrta Doğu Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. FEVZİ SUAT KADIOĞLU